 |  | 
Millermatic 180 Auto-Set MIG Welder and Small Cart 907312011
From now until September 30, 2010 get a $50 Cash Rebate from Miller when you purchase any Millermatic 180 MIG welder AND a Spoolmate 100 spool gun.
You don't have to be an expert to get great welds with the Millermatic 180 MIG welder. This compact, portable package delivers a maximum output of 180 amps and is ideal for maintenance, auto body and fabrication projects.
The Millermatice 180 is easy to use and move.
Applications/Processes
Light Industrial Applications
Light Fabrication
Maintenance and Repair
Auto Body
Farm and Ranch
Home
Flux Cored (FCAW) (gas and self-shielded)
MIG (GMAW)
Features:
New! Auto-Set is a breakthrough control that automatically sets your welder to the proper parameters. Auto-Set offers all-in-one MIG, minus the guesswork!
NEW! Smooth-Start patent-pending
technology provides a smooth, spatterfree
start. It’s the best-starting machine
in the small MIG machine category.
No pop gun starts and no spatter to
clean up.
Infinite Voltage Control with Manual
On/Off Wire Feed Speed Tracking
provides a broader operating range with
finer control by automatically increasing
or decreasing wire feed speed when
voltage is adjusted (unit shipped with
wire feed speed tracking set to “off”).
NEW! More output. Semiautomatic
constant voltage wire welding package
is capable of welding 24 gauge up to
5/16 in (0.8 – 7.9 mm) mild steel.
Durable cast aluminum feedhead incorporates dual-groove quick-change
drive roll and spring-loaded tension arm
with calibrated tension knob all designed
to make set up easier and faster.
Miller’s exclusive “Tip Saver”
short circuit protection shuts down
output when tip is shorted to the work.
Extends contact tip life and protects
internal components from damage.
Trigger reset permits quick reset at
torch rather than unit.
Easy access to output studs provides
convenient polarity changeover when
changing from solid or flux cored wires.
Thermal overload protection shuts down
unit and activates over temperature light
if airflow is blocked or duty cycle is
exceeded. Automatically resets when
fault is corrected and unit cools.
Standard built-in solid-state contactor
circuit makes wire electrically “cold”
until trigger is pulled, making the unit
safer. It’s also easier to position torch
to work before starting weld.
Self-resetting motor protection
circuit eliminates the need to
find and replace fuses.
Uses 4 or 8 in (102 or 203 mm)
spools and can be set up to
weld with wire sizes .024 –
.035 in (0.6 – 0.9 mm) mild/
stainless steel and .030–.045 in
(0.8–1.2 mm) flux cored.
NEW! direct connect with optional Spoolmate 100 Spoolgun for welding with
.030 –.035 in (0.8 – 0.9 mm)
aluminum wire on 14 gauge
to 1/4 in material.
Comes Complete with:
Power source
running gear/cylinder rack
6 ft (1.8 m) power cord and plug
10 ft (3 m), M-100 MIG gun and cable assembly
10 ft (3 m) work cable and clamp
Smith Argon and AR/CO2 mix regulator/flow
gauge with hose
Spool of Hobart .030 in (0.8 mm) solid wire
Two contact tips for .024 in (0.6 mm) wire and
two contact tips for .030 in (0.8 mm) wire
Dual groove quick-change drive roll for .024 in
(0.6 mm) or .030/.035 in (0.8/0.9 mm) wire
Factory-installed gas solenoid valve
Information/settings chart
Order Spoolmate 100 spool gun in the drop down box below to qualify for rebate.
A mail-in rebate form will be sent with your order.
Free standard ground shipping within contiguous U.S.
|
All prices shown are in U.S. Dollars
The Cyberweld® name, logo and the slogan "Weld with your mouse"® are registered service marks of:
J.W. Goodliffe & Son, Inc.
1900 E. Elizabeth Ave.
P.O. Box 4370
Linden, NJ 07036
(800) 419-0580 FAX (908) 486-9366
Phone answered live M-F 8:00am to 4:30pm EDT
© 2000 - 2010. All rights reserved.
|
|
