By jesse from pa on January 5, 2016
can this be run off of a miller bobcat 250?
By Customer Service on January 5, 2016
Answer:The Miller S22A Wire Feeder 951190 cannot be run off of a Bobcat 250
By Antonio from Philadelphia,pa on November 10, 2015
Will this work with a miller symicrowave 350?
By Customer Service on November 11, 2015
Answer:The Miller S22A Wire Feeder 951190 will NOT work with a Syncrowave 350. The Syncrowave is a tig welder and produces constant current(CC)weld output . The S22A needs to be connected to a power source that constant voltage(CV) weld output.
By Jerry from Sacramento, CA on September 17, 2013
I have an ALT 304 miller inverter machine. Does this feeder need a run in control or will this unit work fine as the base model?
By Customer Service on September 18, 2013
Answer:The Miller S22A Wire Feeder 951190 will work with the ALT 304.. It does not have run in control as configured
By tditty from Southwest Fl. on October 20, 2016
Can this be used with a Dynasty 210?
By Customer Service on October 20, 2016
Answer:The Dynasty 210 is a stick/tig welder. It produces Constant Current (CC) weld output. The Miller S22A Wire Feeder 951190 will require a power source the produces Constant Voltage (CV) weld output.. The S22a will not work with the Dynasty
By john from wisconsin on February 13, 2014
i have miller bob cat welder. cant I just add a transformer to power the feeder to hook up this feeder. trying to find a cheaper unit to run.
By Customer Service on February 13, 2014
Answer:The Miller S22A Wire Feeder 951190 cannot be installed on a Miller Bobcat.. The S22a has a 14 pin interconnecting cable that provides the feeder with its operating voltage and also communicates this the power source.. The Bobcat does not have a receptacle to accept this interconnecting communication cable
By Larry from Missouri on March 9, 2016
I have a Miller 330ST Aircrafter. Can I run this off of that? Thanks.
By Customer Service on March 11, 2016
Answer:Miller S22A Wire Feeder 951190 will not run off a Miller 330ST Aircrafter. Here are some of the recommended power sources:
Invision™ 352 MPa and 450 MPa
By JIMMY TILLMAN from LAKE WALES FL. on November 24, 2015
CAN I PURCHASE WITHOUT THE BERNARD MIG GUN?
By Customer Service on November 24, 2015
Answer:You can purchase a Miller S22A feeder without the Bernard Mig gun package. The part number for this item is 300615 and your cost would be $996.96. This is the feeder only and does not include drive rolls. You would have to place your order by phone and we would have to special order it for you
By phin from maine on May 1, 2013
I am looking to have a high duty mig welder attached to to my Miller bobcat for power. Is this the correct unit to be looking at. Welding mild steel up to 1/2 inch all position. I would like to use flux core. Thanks
By Customer Service on May 2, 2013
Answer:The Miller S22A Wire Feeder 951190 is not a good choice for use with a Miller Bobcat since it does not have a 14 pin receptacle in which to connect the s22a feeder.. A better choice would be the Miller SuitCase X-TREME 12VS Wire Feeder 951543..
By Todd from nc on July 22, 2014
I have a miller xmt 304 cc/cv inverter machine will this feeder work with this machine and if so is this the only thing i need to buy.
By Customer Service on July 22, 2014
Answer:The Miller S22A Wire Feeder 951190 will work with your XMT 304 CC/CV..This will be a direct plug in.. This unit will be set up to run .035/.045 wire.. If you do not plan to run these wire sizes you will need to purchase at set of drive rolls, contact tips, and possibly a gun liner to match your wire size.
By David Schwartz from NE PA on December 19, 2013
Will the S22A work with an older Miller XMT 300 CC/CV?
By Customer Service on December 19, 2013
Answer:The Miller S22A Wire Feeder 951190 can be used with an XMT 300 CC/CV.. The XMT 300 CC/CV has two remote receptacles on the front. .One is a 14 pin and the other is a 17 pin.. You would use the 14 pin to connect the feeder to the XMT
By John from Sulphur LA. on February 13, 2015
Can the Miller S22A be ran off a Millermatic 250x?
By Customer Service on February 13, 2015
Answer:A Miller S22A Wire Feeder 951190 cannot be run off of a Millermatic 250X
By John from Sulphur LA. on February 16, 2015
We have a Miller s-22a 24v wire feeder. We need to know what we can use for a power supply.I found it when I was going through some things the other day and thought we would be able to use it. I just need to know what i can use for the power supply.
By Customer Service on February 17, 2015
Answer:The Miller S22A Wire Feeder 951190 can be used with any of the following families for Miller welders.. CP series, Deltaweld series,Dimension series, XMT series..
By Earl from BelleFourche,SD on April 3, 2014
How long is the bernard mig gun that comes with it?
By Customer Service on April 3, 2014
Answer:The Miller S22A Wire Feeder 951190 comes with 15FT Bernard Mig Gun