By Luis Veliz from Guatemala on June 7, 2016
Hi is Luis again
I don't need both torches, if you can give me a good price for the
152 plasma cutter with the 7-5221 torch (and can you keep the other torch) I'll buy it.
By Customer Service on June 8, 2016
Answer:Sorry but the Thermal Dynamics Cutmaster 152 Plasma Cutter w/20 ft Torch 1-1730-1 comes pre packaged and we do not make any substitutions to these packages.
By gerry from brantford ont on August 31, 2012
i have a cut master 152 and was hopeing i could hook it up to 220 volt is it possable and if so would you send me the specs to wire it for 220 volt? thank you
By Customer Service on August 31, 2012
Answer:The Thermal Dynamics Cutmaster 152 Plasma Cutter 1-1730-1 is designed to run on 208/230-460 volt power single or three phase..it is set up to run 208/230 single phase right out tof the box..It will run 220volt single phase in this configuration.There is a hi /lo switch on the back of the machine if you need to run it on 460 volt..If you need to run on 3phase power you will need to go remove the machine cover and go inside the machine to make a change.This change over procedure is covered in the owners manual..If you do not have the manual that came with the machine you can contact thermal dynamics directly and they can provide you with one
By john from firstname.lastname@example.org on January 1, 2014
where is it made?
By Customer Service on January 2, 2014
Answer:The Thermal Dynamics Cutmaster 152 Plasma Cutter 1-5130-1 is made in Mexico with global sourced parts..
By Rik from WY on March 14, 2014
work well on sheet metal?
By Customer Service on March 18, 2014
Answer:The Thermal Dynamics Cutmaster 152 Plasma Cutter 1-1730-1 can be used on sheet metal.. However to get the best cut you should use a lower amperage tip to match the thick ness of the material you are cutting and then adjust the output of the machine to match the material
By Don from Glasgow Montana on November 14, 2014
How big of a breaker do I need to operate to full capability.
By Customer Service on November 17, 2014
Answer:Depending on what input voltage you plan on running the Thermal Dynamics Cutmaster 152 Plasma Cutter 1-1730-1 at the amperage requirements will be different. If you run it on 230 volt 1phase the 152 will draw 120amps. At 230 volt 3phase it will draw 56 amps and on 460 volt 3phase it will draw 37 amps
By Roy Thieding from Maize Kansas on March 23, 2015
will tis unit work with a cnc table
By Customer Service on March 24, 2015
Answer:The Thermal Dynamics Cutmaster 152 Plasma Cutter 1-1730-1 can be made to work with a CNC table.. In order to do this you will need these additional Thermal Dynamics items......Automation Interface Kit 9-8311 ( $229.00)...
25ft CNC cable 9-1008 ($87.74)... Automation Torch 7-4001 (707.00).. We do not stock these items they would have to be special ordered.
By DENNIS from COLTON, CA on November 30, 2014
I HAVE A MILLER 800 DUO AIR PAC AND THE 3-PHASE POWER IS 240 V 50 A, WILL THIS 152 PLASMA CUTTER RUN FULL POWER OFF IT?? THANK YOU DENNIS
By Customer Service on December 1, 2014
Answer:We have discussed your questions with both Miller and Thermal Dynamics.The 800 Duo Air Pak will produce 27kw peak or 20kw continuous on three phase. The Thermal Dynamics Cutmaster 152 Plasma Cutter 1-1730-1 will require 22.5 kw on 240 3 phase. Basically the Cutmaster can be run off of the 800 Duo however you will not be able to run it at maximum capacity
By john heath from UK on March 27, 2014
Can you ship this product to the UKánd if so at what cost? also are your prices displayed plus or inclusive of any government sales tax (VAT). If the machine is exported to the uk does this have to be paid to you in the US?
By Customer Service on March 27, 2014
Answer:We do not ship directly to the UK we use an exporter for this. If you want to purchase a Thermal Dynamics Cutmaster 152 Plasma Cutter 1-1730-1 you would need to place your order through our site.. The site will provide you with the costs for shipping.. At this point you can decide to go ahead with the order or you can opt out of the order at this point at this point
By Jon Olse from Giddings, Tx on December 6, 2012
can you cut 12 guage neatly with this machine?
By Customer Service on December 7, 2012
Answer:You can cut 12 gauge with the Thermal Dynamics Cutmaster 152 Plasma Cutter 1-1730-1 . You would need to change to a 20 amp tip (9-8205) then lower the amperage dial setting down to 20 amps
By Jorge from Sacramento, Ca. on December 15, 2014
I want to buy a model 1-1733-2: 460V 3ph and 180° mechanized torch 50 ft
Please send quote to my email
By Customer Service on December 16, 2014
Answer:In order to receive a formal quote for the item you are looking you need to email email@example.com and request an email quote.
By BINNIE from MUSCATINE IOWA on November 6, 2012
PART # FOR ELECTRODES, TIPS, START CARTRIDGE AND SHIELD CUP