Miller® D-74 MPa Plus Dual Wire Feeder 951292
The Miller® D-74 MPa Plus dual wire feeder is optimized for use with Miller Invision™ MPa and XMT™ MPa welders and can perform two completely different weld procedures without costly change outs. It is capable of synergic pulsed MIG welding and is able to hold up to four independent welding programs that can easily be retrieved for faster set up. The D-74 MPa Plus can also operate with Miller push-pull aluminum MIG guns and has adjustable weld sequence control.
The Miller D-74 MPa Plus comes with digital volt and wire feed speed (amp) meters and is capable of remote voltage control. It is a heavy industrial, four drive roll, 24 VAC wire feeder for MIG and flux-cored welding wires. The D-74 MPa Plus feeds .023 to 5/64 diameter welding wire at a wire feed speed range from 50 to 780 inches per minute. It comes standard with trigger hold, dual tension control, adjustable run-in, and tool-less rotatable drive. Floating positive drive system provides smooth, trouble-free feeding of a variety of welding wires.Processes
Pulsed MIG (GMAW-P)
Flux Cored (FCAW) (gas and self-shielded)
Two independent wire drive systems allow two different welding procedures to be performed by the same welding power source without costly change outs.
Adjustable run-in control for improved arc starts.
Adjustable weld sequence control gives operator complete control of the welding parameters:
preflow, run-in, weld time, crater, burnback and postflow.
Welding process range control locks parameters at a set percentage of welding parameters
to ensure welding procedures and quality standards are maintained on the shop floor.
Dual schedule and trigger program select allows operator to switch
welding parameters without readjusting machine, eliminating downtime and enhancing quality.
Push-pull capability provides consistent, versatile and dependable aluminum wire feeding
over greater distances.
Synergic pulsed MIG operation with MPa power supplies. Provides communication between
the power source, feeder and gun. As wire speed increases or decreases, the pulse parameters
also increase or decrease to match the right amount of power needed.
Trigger schedule select allows the operator to select the alternative schedule by quickly
tapping the gun trigger when not welding. When optimized with MPa power sources the
operator can also switch from MIG to pulsed MIG.
Profile Pulse™ provides TIG appearance with MIG simplicity and productivity. Achieve
"stacked dime" weld bead appearance without
back-stepping. Profile Pulse frequency can be
changed to increase or decrease the spacing
between the ripple pattern to achieve the
desired weld appearance.
Accu-Mate™ properly seats the power pin for best feeding performance and prevents
Accu-Mate grooved MIG guns from sliding in the casting.
Digital meters for easy viewing of the wire feed speed and voltage.
Remote voltage control allows operator to set voltage at the wire feeder without having to go
back to the power source.
Tachometer feedback to help keep wire feed speed accurate.
Toolless rotatable drive assembly allows operator to rotate the drive housing, eliminating severe bends in the wire feed path which reduce gun liner life. Also aids in feeding difficult wires.
Trigger receptacle oriented in a downward position to reduce potential damage.
Trigger hold allows operator to make long welds without having to hold the trigger continuously. Reduces operator fatigue.
Posifeed™ Wire Drive Assembly Features
24 VDC high-torque, permanent-magnet motor.
Quick-change drive rolls.
Quick-release, calibrated drive-roll pressure adjustment arm allows drive roll change without losing spring preload setting.
Four sealed ball bearing all-gear-driven drive-roll carriers for smooth, positive and accurate wire feed with long uninterrupted service life.
Easy loading and threading of welding wire without having to release the drive-roll pressure arm.
Solid-state speed control and brake circuit eliminates the need for electrical/ mechanical relays and increases service life.
Uses Miller standard 1-5/8 in (41 mm) diameter drive rolls.
Quick-connect for all Miller guns.
Covered drive rolls - easy access, heavy-duty, molded composite cover over drive assembly.
Floating positive drive system provides trouble-free feeding on a variety of wires.
Comes Complete With:
D-74 MPa Plus Dual Wire Feeder
Digital voltage and wire feed speed (amp) meter
Remote voltage control
2 - 15 ft. Bernard® Q-400 MIG Welding Gun
Two sets of .035 and .045 inch V groove drive rolls
Standard 10 ft 14-pin interconnecting cord is included
Free Miller® T94i™ ClearLight™ auto-darkening welding hood ($666.42 MSRP Value).
PLUS get a FREE Miller® T94i™ ClearLight™ auto-darkening welding helmet ($666.42 MSRP Value) with the purchase of this Miller® D-74 MPa wire feeder. Free item ships with feeder. (No substitutions allowed). Expires 9/30/22.
The Miller® T94i™ welding helmet features integrated grind shield and Miller's ClearLight™ auto-darkening lens technology that provides a bright, crisp, clear view of the weld puddle. The T94i integrated grind shield is the largest in the industry. With 44 square inches of clear grind shield viewing, all your grinding and other non-welding tasks can be performed quickly and safely.
The Miller T94i is designed to perform in high-heat*, industrial welding applications. The matte silver finish reflects heat while the aluminum heat shield protects the auto-darkening welding lens. The lens operates in Weld, Cut, Grind and X-Mode™, which is ideal when welding with low amperage DC TIG, with obstructed views of the welding arc or while welding outdoors. It is capable of DC TIG welding down to 3 amps and has four arc sensors.
The T94i helmet shell comes standard with shade 5 side windows to improve peripheral vision while welding and easily accommodates a Miller half-mask respirator under the hood.
ClearLight™ lens technology optimizes contrast
and clarity in welding and light states - reducing eye strain and operator fatigue
Integrated grinding shield has 44 square inches of viewing area, the best in the industry.
Aluminum heat shield protects the digital lens in high amperage applications
Weight: 25.7 oz. (729 g) - Lightweight, well-balanced design reduces
neck torque, minimizing operator fatigue and strain.
Matte silver shell reflects heat to keep helmet and user cool
Shade 5.0 side windows enhance peripheral
vision, amplifying sense of surroundings.
Chiseled shell design provides optimal
skin coverage while easily accommodating a
Miller® half mask respirator.
Convenient quick release provides easy access for front cover lens changes
Helmet locks in upright position, allowing user
to keep helmet on for non-welding tasks.
Digital Controls With Four Operating Modes -
X-Mode Electromagnetic Arc Sensing for: Sunlight interference outdoors, Low-Amperage TIG, Pipe/Curves, Obstructed Sensors & Hidden/Cavity Welds
Infotrac™ 2.0 allows for monitoring of arc time and arc count
Half-Shade settings allow for precise lens adjustments based on the environment
Simplistic digital lens interface allows for easy adjustment with or without gloves.
Integrated mag lens holder
Lithium batteries with solar assist; up to 3,000 hours of life
Meets ANSI Z87.1-2015 standard
Improved headgear features additional settings for better fit & comfort
- Weld Mode™ Shades #8 - 13
- Cut Mode™ Shades #5 - 8
- Grind Mode - Light State #3
- X-Mode™ Shades #8 - 13
*May not be suitable for some amperage/temperature extremes.
Comes complete with
5 outside cover lenses
2 inside cover lenses
2 side window covers
This item ships Free via standard ground shipping within contiguous U.S.