Miller® Dynasty® 280 DX Multiprocess Welder With CPS 907514007
The Miller® Dynasty® 280 DX Multiprocess welder with CPS (Cooler Power Supply) is capable of stick and advanced AC/DC TIG welding and has CV circuitry for MIG welding. When paired with a Miller voltage sensing wire feeder, the 280 DX multiprocess is the only welder you'll need on the jobsite to perform MIG, Stick, AC/DC TIG welding and air carbon arc gouging.
The Dynasty 280 DX multiprocess has built in TIG pulse and advanced AC wave forms and provides up to 280 amps of welding output. At just 55 pounds, the Dynasty 280 DX multiprocess can weld materials up to 3/8 inch thick, yet weighs hundreds of pounds less than comparable welders in the same welding output class. When using a water-cooled TIG torch, the 280 DX multiprocess utilizes Cooler-On-Demand™ technology to save energy and prolong the life of your optional TIG torch and Miller Coolmate™ 1.3 cooler.
IP23 rating Ś This equipment is designed for outdoor use. It may be stored, but is not intended to be used outside during precipitation unless sheltered.Processes
AC/DC TIG (GTAW)
Pulsed TIG (GTAW-P)
Air carbon arc (CAC-A)
MIG (GMAW) - when paired with voltage sensing feeder.
Pipe and tube fabrication
Maintenance and repair
Built-in CV circuitry for MIG welding when paired with a Miller voltage sensing feeder.
The DX model offers full AC features, including advanced waveforms and wide ranges of balance and frequency.
Built-in pulser reduces heat input; adds arc stability.Upgradeable and expandable.
Front panel memory card data
port provides the ability to easily
upgrade software and expand
Pro-Set™ feature (professional
eliminates the guesswork
when setting weld parameters.
Use Pro-Set when you want
the speed, convenience and
confidence of pre-set controls.
Simply select the feature and
adjust until Pro-Set appears on
the display. The Pro-Set feature is
available for Balance, Frequency,
Pulse, and DIG parameters.
This programmable feature will
power down the machine if it sits
idle for a specific time.
Auto-Line™ provides state-of-the-art flexibility by automatically connecting to 208-575 VAC, single- or three- phase power without removing the covers to relink the power source. No longer is there a concern if you have the correct machine for the shop or the job site.
Cooler Power Supply (CPS). An
integrated 120-volt dedicated-use
receptacle to power the Coolmate™ 1.3.
The power switch on the Dynasty also
activates the receptacle to help prevent
Lift-Arc™ starting provides x-ray clean
welds in AC or DC arc starting without
the use of high frequency.
starter for non-contact arc initiation.
Provides more consistent arc starts and
greater reliability compared to traditional
HF arc starters. Easy to
set and increases
Digital meters can be calibrated to a
standard device for certification.
Wind Tunnel Technology™ protects internal electrical
components from airborne contaminates, extending the
Fan-On-Demand™ power source cooling system operates
only when needed, reducing noise, energy use and the
amount of contaminates pulled though the machine.
Cooler-On-Demand™ feature operates
only when needed,
energy use, and airborne contaminants pulled
through the cooler.
Thermal Overload Protection -
Internal components are protected from damage by thermal overload protection which automatically shuts down the unit if duty cycle is exceeded or air flow and cooling are restricted.
Wireless remote compatible - fully compatible with Miller
wireless remote control solutions Ś
so you can work the way you want
IP23 rating - This equipment is designed for outdoor use. It may be stored, but is not intended to be used outside during precipitation unless sheltered.
AC TIG Features
AC Pulsed TIG standard
0.1 to 500 PPS
AC Balance (50-99%) controls the amount of oxide cleaning (amperage time in EN) which is essential for high quality welds on aluminum.
AC frequency (20-400 hz)controls the width of the arc cone and the force of the arc.
Advanced AC Waveforms
DC TIG Features
DC Pulsed TIG standard
0.1 to 500 PPS
Exceptionally smooth and precise arc for welding exotic materials.
CV output of the power source gives this unit
MIG process capabilities when paired with a
SuitCase® 8VS (or other voltage sensing
feeder). The feeder is powered off of the
arc voltage of the power source and can run
both solid and flux-cored wires
Stick Features (AC/DC)
Tailored arc control (DIG)
arc characteristic to be changed for
specific applications and electrodes.
Smooth running 7018 or stiffer, more
Hot Start™ adaptive control provides
positive arc starts without sticking.
AC frequency control
adds stability for
smoother welds when AC Stick welding.
Stick-Stuck detects if the electrode is
stuck to the part and turns the welding
output off to safely and easily remove
the electrode. Menu selectable.
Comes complete with
Dynasty® 280 DX CV Welder with CPS (Cooler Power Supply)
Quick Reference Guide (English)
Adjustable shoulder strap
8 ft (2.4 m) primary cord
(2) Dinse 50-mm connectors
(2) Dinse to Tweco® adapters
8 ft. 1/0 wire feeder connection cable with Tweco® connectors
This item ships Free via standard ground shipping within contiguous U.S.