Home  //  Shop All Brands  //  ESAB  //  Tweco MIG & Manual Products  //  Tweco Mini MIG Gun - HB35

Tweco Mini MIG Gun - HB35

Code: HB35M10
Tweco Mini MIG Gun - HB35+ CLICK IMAGE TO ENLARGE
Cyberweld Price: $187.50
Mfg Industrial Price: $250.00
You Save:  $62.50
Rear Connection:  Wire Diameter: 
Availability: Usually ships the next business day
QTY:
McAfee SECURE sites help keep you safe from identity theft, credit card fraud, spyware, spam, viruses and online scams



Tweco® Mini MIG Gun - HB35

Genuine Tweco® Mini MIG 10 ft. (3M) 160 Amp Air-Cooled Mini-MIG Gun kit with rear connections for use with 100-180 amp hobby type welding machines.

Features
  • Neoprene conductor tubes
  • Strain relief and cable support
  • Includes rear connection plug for Miller or Lincoln 100 to 180 amp welding machines

    This item ships Free via standard ground shipping within contiguous U.S.

  • 13 Questions & 14 Answers
    Jay Greenstein`
    from Crystal River Florida asked:
    August 17, 2016
    I am looking for a way to solder/weld Pewter pendents to pewter name tags , will this mini mig work for that or will it melt it ?
    1 Answers
    We are not familiar with working with pewter.The Tweco Mini MIG Gun - HB35 by itself cannot weld it needs to be connected to a mig welder. In most cases the mig welder will produce to much heat to weld pewter.. You should look for a lower temperature operation like soldering
    Customer Service
    on August 18, 2016

    Chris C
    from GA asked:
    April 3, 2016
    Will the HB35 mini mig gun fit a miller 212 auto set mig
    1 Answers
    The Tweco Mini MIG Gun - HB35can be installed on a Millermatic 212. You would have to order part # HB35M10 which is a Mini Mig Gun with a Miller back end connection. Keep in mind that the Mini Mig is only rated at 180 amps and the Millermatic 212 is capable of producing 210 amps. If you operate the 212 at max output using Mini Mig Gun it will eventually overheat and cause premature gun failure
    Customer Service
    on April 4, 2016

    YIANNI
    from massachusetts asked:
    September 2, 2015
    WILL IF FIT THERMAL ARC 181I?
    1 Answers
    The Tweco Mini MIG Gun - HB35 cannot be installed on a Thermal Arc 181i. The HB-35 has a 2 pin trigger switch connection. The 181i uses an 8 pin trigger switch connection.
    Customer Service
    on September 3, 2015

    Bob
    from Moreno Valley ca. asked:
    February 19, 2015
    I need the trigger switch for this gun Tweco mini do you sell just the switch and
    1 Answers
    The trigger switch for theTweco Mini MIG Gun - HB35 is part # 35-90.. They are $15.27 each, We currently do not have any on stock.
    Customer Service
    on February 20, 2015

    geojud4@dslextreme.com
    from san diego ca asked:
    January 22, 2015
    I'm looking for the tweeco mini gun converstion complete for miller 35 ?
    2 Answers
    You can install a Tweco Mini MIG Gun - HB35 on your Millermatic 35. You will also need a Tweco MK35M35 adapter kit ($216.00). This kit is not a stock item and we would have to special order it for you.
    Customer Service
    on January 23, 2015
    You can install a Tweco Mini MIG Gun - HB35 on your Millermatic 35. You will also need a Tweco MK35M35 adapter kit ($216.00). This kit is not a stock item and we would have to special order it for you.
    Customer Service
    on January 23, 2015

    David
    from San Antonio, TX asked:
    April 27, 2014
    will this fit a 20 yr old century 145 amp wire feed with gas?
    1 Answers
    It is very possible that the Tweco Mini MIG Gun - HB35 can fit your century welder.. However it will probably need a adapter kit.. You should contact Tweco directly and speak to their technical dept to determine if this installation can be made.. You can call them at 800-426-1888
    Customer Service
    on April 28, 2014

    Spencer
    from Tempe, Arizona asked:
    February 27, 2014
    Would this fit a Thermal Arc 211i fabricator?
    1 Answers
    No the Tweco Mini MIG Gun - HB35 fits a Miller machine.. You would need a Tweco 35-10 (1000-1131) and a 2060-2141 trigger cable.. Both items would be a special order
    Customer Service
    on February 28, 2014

    John Barber
    from Houston, Tx. asked:
    February 3, 2014
    What code do I use to order anHB-35 mini mig to fit a Lincoln 140c?
    1 Answers
    To install the Tweco Mini Mig gun on your Lincoln 140c you will need to a Tweco 35k174c / 2000-2169 mig gun adapter and a Tweco 3510 mig gun.. The cost for the adapter in $56.76 and the mig gun is $207.75.. These are not stock items and are special order
    Customer Service
    on February 3, 2014

    Mike Crawley
    from Columbus, OH asked:
    July 28, 2013
    I have an older Millermatic 200 circa 1983 vintage full time fan, I do mostly body work, auto repair, trailer and general fab work. Nothing over 1/4" and generally have always used .035 in an old GA15C gun. I Still have the original gun GA25c I think and it works although getting a bit rough. Looking for a lightweight gun for sheet metal and general as above. Want to try a Tweco gun I think. Recommendations? The welder itself is in good shape as has been basically sitting the last 20 years.
    1 Answers
    The Tweco Mini MIG Gun - HB35 can be used on your older Millermatic 200..The Mini Mig is going to limit the weld output to 160 amps and the gun is only 10ft long. When ordering this gun you must be sure to order the Mini Mig with the Miller back end. You could also use the Miller M-100 MIG Gun 248282 . You would still have the same amperage and length limitations that you would have with the Tweco
    Customer Service
    on July 30, 2013

    butters
    from tx asked:
    June 5, 2013
    will it fit millermatic 140 autoset? rearend looks a bit different
    1 Answers
    The Tweco Mini MIG Gun - HB35 will fit the Millermatic 140 auto set.. When ordering you must choose the Miller rear connection
    Customer Service
    on June 11, 2013

    chris
    from Riverside California asked:
    June 4, 2013
    will this gun work on a millermatic 35?
    1 Answers
    If the Millermatic has a serial # before JA------ then there is no replacement gun available.. After serial # JA------ you can use a miller M-25 mig gun.. The Tweco Mini MIG Gun - HB35 is not the correct gun
    Customer Service
    on June 4, 2013

    george Luis
    from florida asked:
    December 7, 2012
    I neet this for a Century 130 Mig wire feed 120 volts
    1 Answers
    The Tweco Tweco Mini MIG Gun - HB35 will not work with a Century 130 welder
    Customer Service
    on December 7, 2012

    allen b.
    from charleston, sc asked:
    September 27, 2012
    will this gun work with an 80 amp century wire welder?
    1 Answers
    The Tweco Mini MIG Gun - HB35 that are listed on the Cyberweld web site are configured to fit Miller or Lincoln model welders..It is possible that a Tweco Mini Mig Gun with the proper adapter can be installed on a Century welder .However more information about the Century welder (serial# and model) would be needed to determine this
    Customer Service
    on September 28, 2012


    Review Summary
    4.7
    3 Reviews
    5
    67% (2)
    4
    33% (1)
    3
    0% (0)
    2
    0% (0)
    1
    0% (0)
    100% Recommend this product (3 of 3 responses)
    By Chris
    marietta GA
    April 22, 2016
    Tweco Mini Mig gun
    I used a Tweco mini mig Gun for 30 years on my old Lincoln welder. When i bought my new Miller. I was glad to see they made the same gun to fit a miller. Very good to get into tight spaces. I am very happy with it.
    By Roger
    San Diego
    October 24, 2014
    Excellent Mig Gun
    Got this to replace a worn out Tweco Mini Mig that lasted about 25 years. Using on a Millermatic 35 (white face), plugged right in and worked like a champ. Hope it lasts as good as the last one.
    ProsSmall, easy to handle and maneuver.
    By Andrew
    Lancaster, Ca
    March 27, 2014
    First tweco gun lasted 15 years continuous use
    Replaced Tweco mini mig on my Hobart Handler.Consumables are readily available when in remote locations.Hobart gun was a headache. People borrow my welder and ask if I want to sell it.
    ProsUniversal consumables low price replacement parts reliability doesn't overheat
    ConsLonger length cable hose tends to slow wire feed if not kept straight so I got the shortest one

    back
    close menu
    Tweco Mini MIG Gun - HB35 detail
    Tweco Mini MIG Gun - HB35