Miller® Trailblazer® 330 Air Pak™ with Excel™ Power, Battery Charge/Crank Assist, Polarity Reversing, Cooler/Separator & Wireless Interface Control (WIC) 907836003
The Miller® Trailblazer® 330 Air Pak™ with Excel™ Power, Battery Charge/Crank Assist, Polarity Reversing, Air Cooler/Separator and Wireless Interface Control is a 330 amp DC engine driven welder and 12,000 watt AC generator that comes complete with a built-in 30 cfm air compressor. The industrial rotary screw air compressor delivers 80-160 PSIG @ 100% duty cycle, with no storage tank. There are four convenient access points for compressed air connections. The compressor runs most types of impact wrenches, even while the Trailblazer's engine is at idle.
The Trailblazer 330 Air Pak's WIC (Wireless Interface Control) gives you full remote welder control; including remote amp/voltage control and engine start/stop. The wireless interface control is a handheld unit that adjusts all weld parameters, stores custom weld settings, displays real time engine status and service intervals, AND acts as a remote engine start/stop. Wireless interface control saves fuel, reduces jobsite noise, and enhances worker safety and productivity by reducing trips back and forth to the welder. The built-in ArcReach® technology allows the Trailblazer 330 Air Pak to communicate directly with a Miller ArcReach wire feeder or remote control through the welding leads, eliminating the need for costly control cables. Miller's exclusive AutoSet™ technology allows you to access pre-programmed welding parameters, based on metal thickness and welding process, for easy set up. You can also fine tune your output amperage and voltage manually, to suit your welding style.
The Miller Trailblazer® 330 Air Pak features a Kohler® 27 horse power CH749 gasoline engine with electric fuel pump, and Miller's exclusive Auto-Speed™ technology. Auto-Speed matches the engine speed with the welding load. This means that the engine can run at optimum RPM rather than full RPM while under load. This translates into reduced fuel consumption, quieter operation and longer engine life. The Trailblazer Air Pak also comes with Excel™ Power, for further cost savings. Excel Power produces a full 2400 watts of auxiliary power while the welder's engine is at idle - saving fuel and reducing jobsite noise. A battery charge/crank assist system is also standard equipment. Get up to 150 amps of output for battery charging and up to 300 amps for cold-crank engine starting. Battery charging cord (300422) must be purchased separately.
The Trailblazer® 330 Air Pak has the most smooth, stable welding arc in the business. It produces X-Ray quality welds whether you are using MIG, Stick or DC TIG welding processes. For MIG welding, the 330 Air Pak has a direct spool gun connection for Miller Spoolmatic® series and Spoolmate™ 200 spool guns, eliminating the need for a WC-24 weld control. For stick welding, the Trailblazer 330 Air Pak's Dynamic Dig™ feature produces a consistent arc that is highly adaptive. Lift-Arc™ DC TIG with Quiet Pulse™ is standard on every Trailblazer 330, and produces outstanding results in TIG welding applications time after time.
Processes (X-Ray Quality)
- Stick (SMAW)
- MIG (GMAW)
- Flux Cored (FCAW)
- DC TIG (GTAW)
- Pulsed DC TIG (GTAW-P)
- Air Carbon Arc (CAC-A) Cutting and Gouging (3/16 in carbons)
- Air Plasma Cutting and Gouging with optional Spectrum models
- AC Generator
Applications
Industrial Applications
Fabrication
Maintenance
Repair
Structural Steel Work
Pipe
Sheet Metal
Features
-
Wireless Interface Control
With wireless interface control, you can change welding processes, adjust parameters, select and save preset programs, turn the machine on/off, get service reminders and more from wherever you are on the jobsite. Extend time between fill ups and maintenance intervals while eliminating the need to go back to your machine to make adjustments.
300 foot operating range from welder to remote
View engine status, fuel level, and battery charge level of remote.
View and select between all available processes.
Turn contactor on/off manually in remote welding mode. Turn engine on/off with remote.
Save custom presets in up to four programs and easily switch between pre-programmed settings.
Quickly adjust and save arc control settings including DIG, DIG range inductance and Auto-Stop.
Adjust amperage or voltage, by increments or percentage, while welding.
-
Polarity Reversing
Reduce downtime when switching between welding procedures. Built-in polarity reversing circuitry allows you to change weld output polarity at the control display, without disconnecting and reconnecting your welding cables.
-
Rotorcomp industrial rotary-screw air compressor
Runs most air impact wrenches at idle and gives 100 percent deliverable air. Produces 30 cfm of air at 100 percent duty cycle and delivers 80–160 psi of air, with no storage tank. Provides four convenient air compressor access points. The air outlet connection requires a 1/2-inch NPT swivel fitting. Compressor is warrantied by Miller for three years.
-
Air Cooler with Separator
Cools and removes moisture from the air supply. Designed for use above 32 degrees Fahrenheit (0°C). Bypass in colder temperatures.
-
ArcReach® standard on all models
ArcReach® technology uses the existing weld cable to communicate welding control information between a Miller® ArcReach® feeder or ArcReach® Stick/TIG remote and Trailblazer® 330 Air Pak™.
This technology eliminates the need for control cords, and their associated problems and costs.
-
Designed for the professional welder
The Trailblazer® 330 delivers unbeatable arc performance in all weld processes, providing the smoothest, most stable arc in the industry.
-
Auto-Set™ technology
Auto-Set offers predefined weld settings to increase ease of use and ensure that the job is done right for operators of all skill levels.
-
Ultra-adaptive arc control
Unlike conventional DIG that provides a preset amount of short-clearing current, Miller-exclusive Dynamic DIG technology works on a time-based algorithm that automatically adjusts the amount of current required to clear a short. Delivers a smoother more consistent arc that can be tailored to match application, material, fit-up and welder technique.
-
Lift-Arc™ DC TIG with Quite Pulse™
DC TIG arc is initiated without the use of high frequency. Simply touch the tungsten electrode to the work piece and lift. Quiet Pulse™ pulsed TIG welding gives you superior control of the welding arc while eliminating the noise typically associated with pulsed TIG welding processes.
-
Direct spool gun connection
Connect a Miller Spoolmatic® Series or Spoolmate™ 200 spool gun directly to the welder. No need for a WC-24 weld control.
-
Smart-Cor™ technology
Independent weld and generator power in an improved, more compact design.
No interaction between jobsite tools and the welding arc, resulting in:
Stronger, cleaner, more efficient generator power
Reduced size and weight
Improved arc performance
-
Auto-Speed™ technology
Automatically adjusts the engine speed to run at lower speeds depending on the total power needed, resulting in:
Exceptional fuel-efficiency
Extended run times
Quieter operation
Reduced emissions
-
Excel™ Power
Excel power provides 120V, 60Hz of pure sine wave generator power at idle speed and while welding. When connected to the Excel power receptacle, you get up to 2400 watts of the cleanest generator power available. Plus, you can run most jobsite tools - like grinders, chop saws, drills and lights at idle speed.
-
Battery charge/crank assist
Reduce downtime with battery charge/crank assist capability. Designed and recommended for mechanics or anyone else responsible for a fleet of trucks or equipment. By using your Trailblazer to charge dead batteries or jump a stubborn engine, you’ll keep your crew working and the fleet up and running.
